SDS - Corteva Transform Isoclast Active Insecticide - 210901

® TM Trademark of Corteva Agriscience and its affiliated companies Page 1 of 12 SAFETY DATA SHEET CORTEVA AGRISCIENCE AUSTRALIA PTY LTD Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 CORTEVA AGRISCIENCE AUSTRALIA PTY LTD encourages you and expects you to read and understand the entire SDS as there is important information throughout the document. This SDS provides users with information relating to the protection of human health and safety at the workplace, protection of the environment and supports emergency response. Product users and applicators should primarily refer to the product label attached to or accompanying the product container. SECTION 1: IDENTIFICATION: PRODUCT IDENTIFIER AND CHEMICAL IDENTITY Product name: Transform™ Insecticide Recommended use of the chemical and restrictions on use Identified uses: End use herbicide product COMPANY IDENTIFICATION CORTEVA AGRISCIENCE AUSTRALIA PTY LTD AUSTRALIA Customer Information Number:

EMERGENCY TELEPHONE NUMBER 24-Hour Emergency Contact: Local Emergency Contact: For advice, contact a doctor (at once) or the Australian Poisons Information Centre: 131 126 Transport Emergency Only Dial 000 SECTION 2: HAZARD(S) IDENTIFICATION GHS Classification Acute aquatic toxicity - Category 2 Chronic aquatic toxicity - Category 2 GHS label elements Hazard pictograms [Image of a GHS environmental hazard pictogram: a tree and a fish in a diamond frame] Signal word: WARNING!

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 2 of 12 Hazard statements Toxic to aquatic life with long lasting effects. Precautionary statements Prevention Avoid release to the environment. Response Collect spillage. Disposal Dispose of contents/ container to an approved waste disposal plant. Other hazards No data available SECTION 3: COMPOSITION AND INFORMATION ON INGREDIENTS, IN ACCORDANCE WITH SCHEDULE 8 This product is a mixture.

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 3 of 12 Indication of any immediate medical attention and special treatment needed Notes to physician: No specific antidote. Treatment of exposure should be directed at the control of symptoms and the clinical condition of the patient. SECTION 5: FIREFIGHTING MEASURES Hazchem code: ●3Z Suitable extinguishing media: To extinguish combustible residues of this product use water fog, carbon dioxide, dry chemical or foam. Unsuitable extinguishing media: No data available Special hazards arising from the substance or mixture Hazardous combustion products: Under fire conditions some components of this product may decompose. The smoke may contain unidentified toxic and/or irritating compounds. Combustion products may include and are not limited to: Sulfur oxides. Nitrogen oxides. Hydrogen fluoride. Carbon monoxide. Carbon dioxide. Unusual Fire and Explosion Hazards: This material will not burn until the water has evaporated. Residue can burn. Advice for firefighters Fire Fighting Procedures: Keep people away. Isolate fire and deny unnecessary entry. Use water spray to cool fire exposed containers and fire affected zone until fire is out and danger of re-ignition has passed. To extinguish combustible residues of this product use water fog, carbon dioxide, dry chemical or foam. Contain fire water run-off if possible. Fire water run-off, if not contained, may cause environmental damage. Review the "Accidental Release Measures" and the "Ecological Information" sections of this (M)SDS. Special protective equipment for firefighters: Wear positive-pressure self-contained breathing apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet, coat, trousers, boots, and gloves). Avoid contact with this material during fire fighting operations. If contact is likely, change to full chemical resistant fire fighting clothing with self-contained breathing apparatus. If this is not available, wear full chemical resistant clothing with self-contained breathing apparatus and fight fire from a remote location. For protective equipment in post-fire or non-fire clean-up situations, refer to the relevant sections. SECTION 6: ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures: Isolate area. Keep unnecessary and unprotected personnel from entering the area. Refer to section 7, Handling, for additional precautionary measures. Use appropriate safety equipment. For additional information, refer to Section 8, Exposure Controls and Personal Protection. Environmental precautions: Prevent from entering into soil, ditches, sewers, waterways and/or groundwater. See Section 12, Ecological Information. Methods and materials for containment and cleaning up: Contain spilled material if possible. Small spills: Absorb with materials such as: Clay. Dirt. Sand. Sweep up. Collect in suitable and properly

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 4 of 12 labeled containers. Large spills: Contact Corteva Agriscience for clean-up assistance. See Section 13, Disposal Considerations, for additional information. SECTION 7: HANDLING AND STORAGE, INCLUDING HOW THE CHEMICAL MAY BE SAFELY USED Precautions for safe handling: Keep out of reach of children. Do not swallow. Avoid contact with eyes, skin, and clothing. Avoid breathing vapour or mist. Wash thoroughly after handling. Keep container tightly closed. Use with adequate ventilation. Spills of these organic materials on hot fibrous insulations may lead to lowering of the autoignition temperatures possibly resulting in spontaneous combustion. See Section 8, EXPOSURE CONTROLS AND PERSONAL PROTECTION. Conditions for safe storage: Store in a dry place. Store in original container. Keep container tightly closed when not in use. Do not store near food, foodstuffs, drugs or potable water supplies. SECTION 8: EXPOSURE CONTROLS AND PERSONAL PROTECTION Control parameters Exposure limits are listed below, if they exist.

Exposure controls Engineering controls: Use local exhaust ventilation, or other engineering controls to maintain airborne levels below exposure limit requirements or guidelines. If there are no applicable exposure limit requirements or guidelines, general ventilation should be sufficient for most operations. Individual protection measures Eye/face protection: Use safety glasses (with side shields). Skin protection Hand protection: Chemical protective gloves should not be needed when handling this material. Consistent with general hygienic practice for any material, skin contact should be minimized. Other protection: No precautions other than clean body-covering clothing should be needed. Respiratory protection: Respiratory protection should be worn when there is a potential to exceed the exposure limit requirements or guidelines. If there are no applicable exposure limit requirements or guidelines, wear respiratory protection when adverse effects, such as respiratory irritation or discomfort have been experienced, or where indicated by your risk assessment process. For most conditions no respiratory protection should be needed; however, if discomfort is experienced, use an approved air purifying respirator. The following should be effective types of air-purifying respirators: Organic vapour cartridge with a particulate pre-filter. Other Information: Selection and use of personal protective equipment should be in accordance with the recommendations in one or more of the relevant Australian/New Zealand Standards, including:

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 5 of 12 AS/NZS 1336: Eye and face protection – Guidelines. AS/NZS 1337: Personal eye protection - Eye and face protectors for occupational applications. AS/NZS 1715: Selection, use and maintenance of respiratory protective equipment. AS/NZS 2161: Occupational protective gloves. AS/NZS 2210: Occupational protective footwear. AS/NZS 4501: Occupational protective clothing Set SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Appearance Physical state: Liquid. Colour: Tan Odour: Mild Odour Threshold: No test data available pH: 4.67 1% pH Electrode Melting point/range: Not applicable Freezing point: No test data available Boiling point (760 mmHg): No test data available Flash point: closed cup > 100 °C Closed Cup Evaporation Rate (Butyl Acetate = 1): No test data available Flammability (solid, gas): Not applicable to liquids Lower explosion limit: No test data available Upper explosion limit: No test data available Vapour Pressure: Not applicable Relative Vapour Density (air = 1): No test data available Relative Density (water = 1): 1.1066 Water solubility: Not applicable Partition coefficient: n-octanol/water: No data available Auto-ignition temperature: 350 °C EC Method A15 Decomposition temperature: No test data available Kinematic Viscosity: No data available Explosive properties: No Oxidizing properties: No, No significant increase (>5C) in temperature. Liquid Density: 1.1066 g/cm3 at 20 °C Digital density meter Molecular weight: No data available NOTE: The physical data presented above are typical values and should not be construed as a specification.

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 6 of 12 SECTION 10: STABILITY AND REACTIVITY Reactivity: No dangerous reaction known under conditions of normal use. Chemical stability: Thermally stable at typical use temperatures. Possibility of hazardous reactions: Polymerization will not occur. Conditions to avoid: Some components of this product can decompose at elevated temperatures. Generation of gas during decomposition can cause pressure in closed systems. Incompatible materials: None known. Hazardous decomposition products: Decomposition products depend upon temperature, air supply and the presence of other materials. Toxic gases are released during decomposition. SECTION 11: TOXICOLOGICAL INFORMATION Toxicological information appears in this section when such data is available. Acute toxicity Acute oral toxicity Very low toxicity if swallowed. Harmful effects not anticipated from swallowing small amounts. As product: LD50, Rat, male and female, > 5,000 mg/kg Acute dermal toxicity Prolonged skin contact is unlikely to result in absorption of harmful amounts. As product: LD50, Rat, male and female, > 5,000 mg/kg Acute inhalation toxicity No adverse effects are anticipated from inhalation. As product: LC50, Rat, male and female, 4 Hour, Aerosol, > 2.21 mg/l No deaths occurred at this concentration. Maximum attainable concentration. Skin corrosion/irritation Prolonged contact is essentially non-irritating to skin. Serious eye damage/eye irritation May cause slight eye irritation. Corneal injury is unlikely. Sensitization Did not demonstrate the potential for contact allergy in mice. For respiratory sensitization: No relevant data found. Specific Target Organ Systemic Toxicity (Single Exposure) Evaluation of available data suggests that this material is not an STOT-SE toxicant. Specific Target Organ Systemic Toxicity (Repeated Exposure) For the active ingredient(s): In animals, effects have been reported on the following organs: Liver.

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 7 of 12 For the minor component(s): In rare cases, repeated excessive exposure to propylene glycol may cause central nervous system effects. Carcinogenicity For the active ingredient(s): Has caused cancer in laboratory animals. However, the effects are species specific and are not relevant to humans. Teratogenicity For the active ingredient(s): Has caused birth defects in laboratory animals at high doses. In laboratory animals, excessive doses toxic to the parent animals caused decreased weight and survival of offspring. However, the effects are species specific and are not relevant to humans. These concentrations exceed relevant human dose levels. Reproductive toxicity For the active ingredient(s): In animal studies, has been shown to interfere with reproduction. However, the effects are species specific and are not relevant to humans. These concentrations exceed relevant human dose levels. Mutagenicity Animal genetic toxicity studies were negative. Aspiration Hazard Based on physical properties, not likely to be an aspiration hazard. SECTION 12: ECOLOGICAL INFORMATION Ecotoxicological information appears in this section when such data is available. Ecotoxicity Acute toxicity to fish For similar material(s): Material is moderately toxic to aquatic organisms on an acute basis (LC50/EC50 between 1 and 10 mg/L in the most sensitive species tested). As product: LC50, Oncorhynchus mykiss (rainbow trout), static test, 96 Hour, > 939 mg/l, OECD Test Guideline 203 Acute toxicity to aquatic invertebrates LC50, Daphnia magna (Water flea), static test, 48 Hour, > 880 mg/l, OECD Test Guideline 202 or Equivalent For similar material(s): LC50, saltwater mysid Mysidopsis bahia, 96 Hour, > 1 - < 10 mg/l Acute toxicity to algae/aquatic plants ErC50, diatom Navicula sp., 72 Hour, Growth rate inhibition, > 100 mg/l Toxicity to Above Ground Organisms Material is practically non-toxic to birds on an acute basis (LD50 > 2000 mg/kg). Oral LD50, Colinus virginianus (Bobwhite quail), > 2250 mg/kg bodyweight. Oral LD50, Apis mellifera (bees), 48 Hour, 0.23 micrograms/bee Contact LD50, Apis mellifera (bees), 48 Hour, 0.59 micrograms/bee

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 8 of 12 Toxicity to soil-dwelling organisms LC50, Eisenia fetida (earthworms), 14 d, 6.4mg/kg dry weight (d.w.) Persistence and degradability Sulfoxaflor Biodegradability: Material is not readily biodegradable according to OECD/EEC guidelines. Biodegradation: 0 % Exposure time: 28 d Method: OECD Test Guideline 310 Theoretical Oxygen Demand: 1.90 mg/mg Photodegradation Test Type: Half-life (indirect photolysis) Sensitizer: OH radicals Atmospheric half-life: 7.762 Hour Method: Estimated. Propylene glycol Biodegradability: Material is readily biodegradable. Passes OECD test(s) for ready biodegradability. Biodegradation may occur under anaerobic conditions (in the absence of oxygen). 10-day Window: Pass Biodegradation: 81 % Exposure time: 28 d Method: OECD Test Guideline 301F or Equivalent 10-day Window: Not applicable Biodegradation: 96 % Exposure time: 64 d Method: OECD Test Guideline 306 or Equivalent Theoretical Oxygen Demand: 1.68 mg/mg Chemical Oxygen Demand: 1.53 mg/mg Biological oxygen demand (BOD)

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 9 of 12 Bioaccumulative potential Sulfoxaflor Bioaccumulation: Bioconcentration potential is low (BCF < 100 or Log Pow < 3). Partition coefficient: n-octanol/water (log Pow): 0.802 at 20 °C Measured Propylene glycol Bioaccumulation: Bioconcentration potential is low (BCF < 100 or Log Pow < 3). Partition coefficient: n-octanol/water (log Pow): -1.07 Measured Bioconcentration factor (BCF): 0.09 Estimated. Sulfonated aromatic polymer, sodium salt Bioaccumulation: No relevant data found. Mobility in Soil Sulfoxaflor Potential for mobility in soil is very high (Koc between 0 and 50). Partition coefficient (Koc): 40 Measured Propylene glycol Given its very low Henry's constant, volatilization from natural bodies of water or moist soil is not expected to be an important fate process. Potential for mobility in soil is very high (Koc between 0 and 50). Partition coefficient (Koc): < 1 Estimated. Sulfonated aromatic polymer, sodium salt No relevant data found. Results of PBT and vPvB assessment Sulfoxaflor This substance is not considered to be persistent, bioaccumulating and toxic (PBT). This substance is not considered to be very persistent and very bioaccumulating (vPvB). Propylene glycol This substance is not considered to be persistent, bioaccumulating and toxic (PBT). This substance is not considered to be very persistent and very bioaccumulating (vPvB). Sulfonated aromatic polymer, sodium salt This substance is not considered to be persistent, bioaccumulating and toxic (PBT). This substance is not considered to be very persistent and very bioaccumulating (vPvB). Other adverse effects Sulfoxaflor This substance is not on the Montreal Protocol list of substances that deplete the ozone layer. Propylene glycol This substance is not on the Montreal Protocol list of substances that deplete the ozone layer. Sulfonated aromatic polymer, sodium salt This substance is not on the Montreal Protocol list of substances that deplete the ozone layer.

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 10 of 12 SECTION 13: DISPOSAL CONSIDERATIONS Disposal methods: If wastes and/or containers cannot be disposed of according to the product label directions, disposal of this material must be in accordance with your local or area regulatory authorities. This information presented below only applies to the material as supplied. The identification based on characteristic(s) or listing may not apply if the material has been used or otherwise contaminated. It is the responsibility of the waste generator to determine the toxicity and physical properties of the material generated to determine the proper waste identification and disposal methods in compliance with applicable regulations. If the material as supplied becomes a waste, follow all applicable regional, national and local laws. SECTION 14: TRANSPORT INFORMATION ADG Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.(Sulfoxaflor) UN number: UN 3082 Class: 9 Packing group: III Marine pollutant: Sulfoxaflor Classification for SEA transport (IMO-IMDG): Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.(Sulfoxaflor) UN number: UN 3082 Class: 9 Packing group: III Marine pollutant: Sulfoxaflor Transport in bulk according to Annex I or II of MARPOL 73/78 and the IBC or IGC Code: Consult IMO regulations before transporting ocean bulk Classification for AIR transport (IATA/ICAO): Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.(Sulfoxaflor) UN number: UN 3082 Class: 9 Packing group: III Hazchem Code: ●3Z Further information: Environmentally Hazardous Substances meeting the descriptions of UN 3077 or UN 3082 are not subject to the Australian Code for the Transport of Dangerous Goods (ADG). This applies when transported by road or rail in packaging’s that do not incorporate a receptacle exceeding 500 kg(L) or IBCs per ADG Special Provision AU01. Marine Pollutants in single or combination packaging containing a net quantity per single or inner packaging of 5 L or less for liquids or having a net mass per single or inner packaging of 5 KG or less for solids may be transported as non-dangerous goods as provided in section 2.10.2.7 of IMDG code and IATA special provision A197.

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 11 of 12 This information is not intended to convey all specific regulatory or operational requirements/ information relating to this product. Additional transportation system information can be obtained through an authorized sales or customer service representative. It is the responsibility of the transporting organization to follow all applicable laws, regulations and rules relating to the transportation of the material. SECTION 15: REGULATORY INFORMATION Poison Schedule: S5 APVMA Approval Number: 64101 SECTION 16: ANY OTHER RELEVANT INFORMATION Revision Identification Number: 101191190 / A143 / Issue Date: 14.09.2021 / Replaces: 6.01.2021 DAS Code: GF-2032 Sections amended: 5, 14 Legend

Product name: TRANSFORM® Insecticide Issue Date: 14.09.2021 ® TM Trademark of Corteva Agriscience and its affiliated companies Page 12 of 12 Recommendations on the Transport of Dangerous Goods; vPvB - Very Persistent and Very Bioaccumulative; WHMIS - Workplace Hazardous Materials Information System. CORTEVA AGRISCIENCE AUSTRALIA PTY LTD urges each customer or recipient of this (M)SDS to study it carefully and consult appropriate expertise, as necessary or appropriate, to become aware of and understand the data contained in this (M)SDS and any hazards associated with the product. The information herein is provided in good faith and believed to be accurate as of the effective date shown above. However, no warranty, express or implied, is given. Regulatory requirements are subject to change and may differ between various locations. It is the buyer's/user's responsibility to ensure that his activities comply with all federal, state, provincial or local laws. The information presented here pertains only to the product as shipped. Since conditions for use of the product are not under the control of the manufacturer, it is the buyer's/user's duty to determine the conditions necessary for the safe use of this product. Due to the proliferation of sources for information such as manufacturer-specific (M)SDSs, we are not and cannot be responsible for (M)SDSs obtained from any source other than ourselves. If you have obtained an (M)SDS from another source or if you are not sure that the (M)SDS you have is current, please contact us for the most current version.

TM ® Trademarks of Corteva Agriscience and its affiliated companies. © 2021 Corteva.