--- title: SDS - PCT Reactor Red Dye - 230801 canonical: https://fernland.com.au/documents/1076/ dateModified: 2026-08-04 03:02:58 summary: Safety Data Sheet type: sds --- # SDS - PCT Reactor Red Dye - 230801 > Safety Data Sheet Product Name: Reactor RED Spray Marker Dye Page: 1 of 5 This version issued: August, 2023 SAFETY DATA SHEET Issued by: PCT Holdings Pty Ltd Phone: (all hours) Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand) Section 1 - Identification of The Material and Supplier PCT Holdings Pty Ltd Phone: (all hours) 1/74 Murdoch Circuit Chemical nature: Dye in a suitable solvent system. Trade Name: Reactor RED Spray Marker Dye Product Use: Liquid marking dye and foam marker colouring agent. Creation Date: June, 2016 This version issued: August, 2023 and is valid for 5 years from this date. Poisons Information Centre: Phone 13 1126 from anywhere in Australia Section 2 - Hazards Identification Statement of Hazardous Nature SUSMP Classification: None allocated. ADG Classification: None allocated. Not a Dangerous Good according to Australian Dangerous Goods (ADG) Code, IATA or IMDG/IMSBC criteria. UN Number: None allocated [GHS Warning Symbol: Exclamation mark inside a red diamond] GHS Signal word: WARNING Acute Toxicity Oral Category 4 Serious eye damage/eye irritation Category 2/2A HAZARD STATEMENT: H302: Harmful if swallowed. H319: Causes serious eye irritation. PREVENTION P102: Keep out of reach of children. P262: Do not get in eyes, on skin, or on clothing. P264: Wash contacted areas thoroughly after handling. P270: Do not eat, drink or smoke when using this product. P280: Wear protective gloves, protective clothing and eye or face protection. RESPONSE P330: Rinse mouth. P352: Wash with plenty of soap and water. P301+P312: IF SWALLOWED: Call a POISON CENTRE or doctor if you feel unwell. P301+P330+P331: IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337+P313: If eye irritation persists: Get medical advice. P370+P378: In case of fire, use carbon dioxide, dry chemical, foam, water fog. STORAGE P402+P404: Store in a dry place. Store in a closed container. P403+P235: Store in a well-ventilated place. Keep cool. DISPOSAL P501: If they can not be recycled, dispose of contents to an approved waste disposal plant and containers to landfill (see Section 13 of this SDS). Emergency Overview Physical Description & Colour: Intensely red liquid. Odour: Slight aromatic odour. Major Health Hazards: may cause serious irritation to eyes, harmful if swallowed. --- Product Name: Reactor RED Spray Marker Dye Page: 2 of 5 This version issued: August, 2023 SAFETY DATA SHEET Issued by: PCT Holdings Pty Ltd Phone: (all hours) Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand) Section 3 - Composition/Information on Ingredients | Ingredients | CAS No | Conc,% | TWA (mg/m³) | STEL (mg/m³) | | :--- | :--- | :--- | :--- | :--- | | Diethylene glycol | 111-46-6 | 60-90 | 100 | not set | | Rhodamine B | 81-88-9 | 15 | not set | not set | | Ingredients said to be not hazardous | secret | to 100 | not set | not set | This is a commercial product whose exact ratio of components may vary slightly. Minor quantities of other non hazardous ingredients are also possible. The SWA TWA exposure value is the average airborne concentration of a particular substance when calculated over a normal 8 hour working day for a 5 day working week. The STEL (Short Term Exposure Limit) is an exposure value that may be equalled (but should not be exceeded) for no longer than 15 minutes and should not be repeated more than 4 times per day. There should be at least 60 minutes between successive exposures at the STEL. The term "peak "is used when the TWA limit, because of the rapid action of the substance, should never be exceeded, even briefly. Section 4 - First Aid Measures General Information: You should call The Poisons Information Centre if you feel that you may have been poisoned, burned or irritated by this product. The number is 13 1126 from anywhere in Australia (0800 764 766 in New Zealand) and is available at all times. Have this SDS with you when you call. Inhalation: No first aid measures normally required. However, if inhalation has occurred, and irritation has developed, remove to fresh air and observe until recovered. If irritation becomes painful or persists more than about 30 minutes, seek medical advice. Skin Contact: Wash gently and thoroughly with water (use non-abrasive soap if necessary) for 5 minutes or until chemical is removed. Eye Contact: Immediately flush the contaminated eye(s) with lukewarm, gently flowing water for 15 minutes or until the product is removed, while holding the eyelid(s) open. Take care not to rinse contaminated water into the unaffected eye or onto the face. Obtain medical attention immediately. Take special care if exposed person is wearing contact lenses. Ingestion: If swallowed, do NOT induce vomiting. Wash mouth with water and contact a Poisons Information Centre, or call a doctor. Section 5 - Fire Fighting Measures Fire and Explosion Hazards: The major hazard in fires is usually inhalation of heated and toxic or oxygen deficient (or both), fire gases. There is no risk of an explosion from this product under normal circumstances if it is involved in a fire. Violent steam generation or eruption may occur upon application of direct water stream on hot liquids. Fire decomposition products from this product may be toxic if inhaled. Take appropriate protective measures. Extinguishing Media: In case of fire, use carbon dioxide, dry chemical, foam, water fog. Avoid the use of water jets. Fire Fighting: If a significant quantity of this product is involved in a fire, call the fire brigade. Flammability Class: Not flammable (GHS); C1 combustible (AS 1940) Section 6 - Accidental Release Measures Accidental release: In the event of a major spill, prevent spillage from entering drains or water courses. Wear full protective chemically resistant clothing including eye/face protection, gauntlets and self contained breathing apparatus. See below under Personal Protection regarding Australian Standards relating to personal protective equipment. Suitable materials for protective clothing include PVC, butyl rubber. Eye/face protective equipment should comprise as a minimum, protective goggles. If there is a significant chance that vapours or mists are likely to build up in the cleanup area, we recommend that you use a respirator. Usually, no respirator is necessary when using this product. However, if you have any doubts consult the Australian Standard mentioned below (section 8). Otherwise, not normally necessary. Stop leak if safe to do so, and contain spill. Absorb onto sand, vermiculite or other suitable absorbent material. If spill is too large or if absorbent material is not available, try to create a dike to stop material spreading or going into drains or waterways. Sweep up and shovel or collect recoverable product into labelled containers for recycling or salvage, and dispose of promptly. Recycle containers wherever possible after careful cleaning. After spills, wash area preventing runoff from entering drains. If a significant quantity of material enters drains, advise emergency services. This material may be suitable for approved landfill. Ensure legality of disposal by consulting regulations prior to disposal. Thoroughly launder protective clothing before storage or re-use. Advise laundry of nature of contamination when sending contaminated clothing to laundry. --- Product Name: Reactor RED Spray Marker Dye Page: 3 of 5 This version issued: August, 2023 SAFETY DATA SHEET Issued by: PCT Holdings Pty Ltd Phone: (all hours) Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand) Section 7 - Handling and Storage Handling: Keep exposure to this product to a minimum, and minimise the quantities kept in work areas. Check Section 8 of this SDS for details of personal protective measures, and make sure that those measures are followed. The measures detailed below under "Storage" should be followed during handling in order to minimise risks to persons using the product in the workplace. Also, avoid contact or contamination of product with incompatible materials listed in Section 10. Storage: Make sure that containers of this product are kept tightly closed. Keep containers dry and away from water. Make sure that the product does not come into contact with substances listed under "Incompatibilities" in Section 10. Some liquid preparations settle or separate on standing and may require stirring before use. Check packaging - there may be further storage instructions on the label. Section 8 - Exposure Controls and Personal Protection The following Australian Standards will provide general advice regarding safety clothing and equipment: Respiratory equipment: AS/NZS 1715, Protective Gloves: AS 2161, Occupational Protective Clothing: AS/NZS 4501 set 2008, Industrial Eye Protection: AS1336 and AS/NZS 1337, Occupational Protective Footwear: AS/NZS2210. | SWA Exposure Limits | TWA (mg/m³) | STEL (mg/m³) | | :--- | :--- | :--- | | Diethylene glycol | 100 | not set | No special equipment is usually needed when occasionally handling small quantities. The following instructions are for bulk handling or where regular exposure in an occupational setting occurs without proper containment systems. Ventilation: No special ventilation requirements are normally necessary for this product. However make sure that the work environment remains clean and that vapours and mists are minimised. Eye Protection: Protective glasses or goggles must be worn when this product is being used. Failure to protect your eyes may lead to severe harm to them or to general health. Emergency eye wash facilities must also be available in an area close to where this product is being used. Skin Protection: You should avoid contact even with mild skin irritants. Therefore you should wear suitable impervious elbow-length gloves and facial protection when handling this product. See below for suitable material types. Protective Material Types: We suggest that protective clothing be made from the following materials: PVC, butyl rubber. Respirator: Usually, no respirator is necessary when using this product. However, if you have any doubts consult the Australian Standard mentioned above. Otherwise, not normally necessary. Eyebaths or eyewash stations and safety deluge showers should, if practical, be provided near to where this product is being handled commercially. Section 9 - Physical and Chemical Properties: Physical Description & colour: Intensely red liquid. Odour: Slight aromatic odour. Boiling Point: >240°C at 100kPa Flash point: >96°C Upper Flammability Limit: No data. Lower Flammability Limit: No data. Autoignition temperature: No data. Freezing/Melting Point: No specific data. Liquid at normal temperatures. Volatiles: No specific data. Expected to be low at 100°C. Vapour Pressure: Negligible at normal ambient temperatures. Vapour Density: No data. Specific Gravity: About 0.945 at 20°C Water Solubility: Soluble. pH: No data. Volatility: Negligible at normal ambient temperatures. Odour Threshold: No data. Evaporation Rate: No data. Coeff Oil/water Distribution: Kow Log P is 1.95 for Rhodamine B Particle Characteristics: Not applicable to liquids. --- Product Name: Reactor RED Spray Marker Dye Page: 4 of 5 This version issued: August, 2023 SAFETY DATA SHEET Issued by: PCT Holdings Pty Ltd Phone: (all hours) Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand) Section 10 – Stability and Reactivity Reactivity: This product is unlikely to react or decompose under normal storage conditions. However, if you have any doubts, contact the supplier for advice on shelf life properties. Conditions to Avoid: Keep containers tightly closed. Containers should be kept dry. Incompatibilities: oxidising agents. Fire Decomposition: Combustion forms carbon dioxide, and if incomplete, carbon monoxide and possibly smoke. Water is also formed. Carbon monoxide poisoning produces headache, weakness, nausea, dizziness, confusion, dimness of vision, disturbance of judgment, and unconsciousness followed by coma and death. Polymerisation: Polymerisation reactions are unlikely; they are not expected to occur. Section 11 - Toxicological Information Local Effects: Target Organs: There is no data to hand indicating any particular target organs. Classification of Hazardous Ingredients | Ingredient | Health Hazard Statement Codes | | :--- | :--- | | Diethylene Glycol | H302 | * Acute toxicity - category 4 For product as supplied LD50 Oral, Rat 400-2000mg/kg Potential Health Effects Inhalation: Short Term Exposure: Available data indicates that this product is not harmful. However product may be mildly irritating, although unlikely to cause anything more than mild transient discomfort. Long Term Exposure: No data for health effects associated with long term inhalation. Skin Contact: Short Term Exposure: Available data indicates that this product is not harmful. It should present no hazards in normal use. However product may be irritating, but is unlikely to cause anything more than mild transient discomfort. Long Term Exposure: No data for health effects associated with long term skin exposure. Eye Contact: Short Term Exposure: This product is a severe eye irritant. Symptoms may include stinging and reddening of eyes and watering which may become copious. Other symptoms such as swelling of eyelids and blurred vision may also become evident. If exposure is brief, symptoms should disappear once exposure has ceased. However, lengthy exposure or delayed treatment is likely to cause permanent damage. Long Term Exposure: No data for health effects associated with long term eye exposure. Ingestion: Short Term Exposure: Significant oral exposure is considered to be unlikely. Available data shows that this product is harmful, but symptoms are not available. However, this product is an oral irritant. Symptoms may include burning sensation and reddening of skin in mouth and throat. Other symptoms may also become evident, but all should disappear once exposure has ceased. Long Term Exposure: No data for health effects associated with long term ingestion. Carcinogen Status: SWA: No significant ingredient is classified as carcinogenic by SWA. NTP: No significant ingredient is classified as carcinogenic by NTP. IARC: No significant ingredient is classified as carcinogenic by IARC. Section 12 - Ecological Information Insufficient data to be sure of status. Expected to not be an environmental hazard. Section 13 - Disposal Considerations Disposal: This product may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for its intended use. If it has been contaminated, it may be possible to reclaim the product by filtration, distillation or some other means. If neither of these options is suitable in-house, consider controlled incineration, or contact a specialist waste disposal company. --- Product Name: Reactor RED Spray Marker Dye Page: 5 of 5 This version issued: August, 2023 SAFETY DATA SHEET Issued by: PCT Holdings Pty Ltd Phone: (all hours) Poisons Information Centre: 13 1126 from anywhere in Australia, (0800 764 766 in New Zealand) Section 14 - Transport Information UN Number: This product is not classified as a Dangerous Good by ADG, IATA or IMDG/IMSBC criteria. No special transport conditions are necessary unless required by other regulations. Section 15 - Regulatory Information AIIC: All of the significant ingredients in this formulation are compliant with AICIS regulations. Section 16 - Other Information This SDS contains only safety-related information. For other data see product literature. Acronyms: ADG Code: Australian Code for the Transport of Dangerous Goods by Road and Rail (7th edition) AIIC: Australian Inventory of Industrial Chemicals SWA: Safe Work Australia, formerly ASCC and NOHSC CAS number: Chemical Abstracts Service Registry Number Hazchem Code: Emergency action code of numbers and letters that provide information to emergency services especially firefighters IARC: International Agency for Research on Cancer NOS: Not otherwise specified NTP: National Toxicology Program (USA) SUSMP: Standard for the Uniform Scheduling of Medicines & Poisons UN Number: United Nations Number THIS SDS SUMMARISES OUR BEST KNOWLEDGE OF THE HEALTH AND SAFETY HAZARD INFORMATION OF THE PRODUCT AND HOW TO SAFELY HANDLE AND USE THE PRODUCT IN THE WORKPLACE. EACH USER MUST REVIEW THIS SDS IN THE CONTEXT OF HOW THE PRODUCT WILL BE HANDLED AND USED IN THE WORKPLACE. IF CLARIFICATION OR FURTHER INFORMATION IS NEEDED TO ENSURE THAT AN APPROPRIATE RISK ASSESSMENT CAN BE MADE, THE USER SHOULD CONTACT THIS COMPANY SO WE CAN ATTEMPT TO OBTAIN ADDITIONAL INFORMATION FROM OUR SUPPLIERS OUR RESPONSIBILITY FOR PRODUCTS SOLD IS SUBJECT TO OUR STANDARD TERMS AND CONDITIONS, A COPY OF WHICH IS SENT TO OUR CUSTOMERS AND IS ALSO AVAILABLE ON REQUEST. Please read all labels carefully before using product. This SDS is prepared in accord with the SWA document “Preparation of Safety Data Sheets for Hazardous Chemicals - Code of Practice” (July 2020) and GHS Revision 7 Copyright © Kilford & Kilford Pty Ltd, August, 2023.